Alignment Tools
Wheel Alignment Gauge
Now you can check wheel alignment in minutes. Tool measures toe-in and toe-out on an easy to read gauge. Lets you adjust alignment to minimize tire wear. Even checks wheel wobble. To use, set gauge at rear of front tires and take measurements. Transfer tool to front and measure the difference. If necessary, adjust tie rods in or out half the distance of the dial reading.
Eezibleed Brake & Clutch Bleeder Kit
Bleed Brakes/Hydraulic Clutches with Pressure - Pressure works better than vacuum because air is not pulled around the bleed fitting. Eezibleed uses a tire or tank set at 20 psi with the included reservoir bottle to inject fresh fluid into the master cylinder as the system is bled. Fits most imported cars. Can fit any vehicle by modifying a spare master cylinder cap by drilling a 3/8" hole and attaching the pressure/fluid hose with the included hardware. Includes pressurizing hose with tire stem fitting, assorted caps to fit many Lockheed and Girling systems, and instructions. Made in the UK.
Mityvac Brake Bleeding Kit
Vacuum tester/brake bleeding kit gives you a clean, quick way to bleed the fluid lines in your vehicles brake system. May also be used on virtually all hydraulic systems! Trigger release for one-hand operation. Reservoir jar creates a vacuum that pulls fluid into the jar with the fluid comes the air bubbles. Includes 24in. of 1/4in. I.D. tubing, rubber cup adapter, reservoir jar storage lid and 40-page instruction book in Spanish and English.
Mityvac Plus Test Kit
Same features as above plus the benefit of a switch-valve for quick change from pressure to vacuum testing without changing hose positions. Comes complete with attachments, caps, jar, hoses, master cylinder kit, and detailed instruction manual.
Phoenix V12 Brake and Clutch Bleeder
Purge trapped air in brake and clutch hydraulic using patented Reverse Fluid Injection technology without a helper and in about 10 minutes. Works on cars, trucks and motorcycles where manual methods and conventional pressure bleeders fail! Includes brake fluid bottle adapter, quick couplers and hoses and instructions. Compatible with all brake fluids.
Fuel Injection Testers - Bosch CIS K-Jetronic
FUEL INJECTION TESTERS Indicates if fuel pump is defective or inconsistent in pressure flow. Quickly, easily pinpoint problems in control pressure regulator or fuel distributor. Eliminates guess work! Includes in-line 2-1/2" diam. gauge, shut-off valve; 6 adapters, hook-up and parts, schematic and instructions.
Hog Ring Pliers Bent Nose
These pliers are the basic tools needed to do upholstery work. Designed just for hog ring installation. Grooved jaws hold the ring securely. The straight pliers are spring loaded to hold rings closed. The angled pliers are spring loaded to stay open. Forged steel with safety grips.
Hog Ring Pliers Straight Nose
These Pliers are the basic tools needed to do upholstery work. Designed just for hog ring installation. Grooved jaws hold the ring securely. The straight pliers are spring-loaded to hold rings closed. The angled are spring-loaded to stay open. Forged steel with saftey grips.
Hog Rings - Pack of 100
Pack of 100 Hog Rings
Steering Wheel Puller
Rivet Nut Tool Kit - STANDARD thread
Basic Rivet Nut Installation Tool - Inexpensive enough to justify using Rivet Nuts instead of the weaker sheet metal screws. This kit makes it easy to install 1/4"-20, and 10-32 rivet nuts. Uses a simple sliding wedge design to seat the rivet nut. Includes 12 1/4"-20 rivet nuts, 12 10-32 rivet nuts, 11/32" and 1/4" drill bits, installation tool and instructions. Made in USA.
Rivet/Nut ThreadSetting Tool Kit - METRIC
Pro Rivet Nut/Thread Setting Tool Kits - Insert threads into sheet metal from one side (like a pop rivet) to mount mirrors, trim and accessories. Both sets include: tool, appropriate mandrels, 75 assorted rivet nuts, and instructions in a molded plastic case. Includes M3x0.5, M4x0.7, M5x0.8, and M6x1.0 rivet nuts.
Rivet Nut and Thread-Sert Tool, Fasteners and Kit
RIVET NUT AND THREAD-SERT TOOL KITS Choose complete rivet nut and thread-sert kit or 3-in-1 rivet/rivet nut/thread-sert tool kit Easy, economical alternatives to riveting! CHOICE OF FASTENERS Rivet Nuts. Most cost-effective way to place permanent threads in thin materials! Perfect for metal, fiberglass and rigid plastic which are too thin to support a threaded screw or bolt with the rivet nut. No drilling out rivets to remove fasteners! Drill a hole in panel or wall, thread rivet nut on mandrel of installation tool and insert into hole. Squeezing handle expands the rear of the rivet nut and locks it in place�ready for insertion of machine screw. Large diameter head allows use in soft materials with little thread strength and to provide the most bearing surface. Threading resists high loads, prevents loosening under vibration. Look neat. Thread-Serts. Best for use with thin or thick materials! Ideal for use in any material at least 3/32" thick. Eliminate need for tapping and welding. Thread-Serts feature an upper sleeve and a base, both with internal and external threads. During installation, base is drawn upwards inside the sleeve, forcing 360degree contact between sleeve and application material. Easy --all you need is installation tool and drilled or punched hole.
Clamshell Strut Spring Compressor by OTC
Servicing DeLorean springs is more convenient and affordable when this tool is in your shop. It fits a wide range of struts/springs and no special adapter shoes are needed. The compressor jaws are held in place by safety lockng pins. Tool compresses springs of 4'' to 9'' O.D. with wire diameters of 7/16'' to 11/16''. It can be driven by an impact wrench. Lifetime Marathon Warranty. Made in USA. Weight: 19 lbs. By OTC.
Trans-X Stop Leak & Tune Up
Ok, so it's not really a tool, but it works like one. Trans-X is compatible with all automatic transmission - power steering - and hydraulic fluids. Effectively stops leaks from hardened or shrunken seals in all hydraulic systems. Use Trans-X in automatic transmissions - power steering - and hydraulic control systems.
