 
Re: [doc] finally driven her!!
    
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [doc] finally driven her!!
- From: "blackaddertoo" <blackaddertoo@xxxxxxxxxxx>
- Date: Sun, 31 Jul 2005 17:22:35 -0000
thanks Richard, i'll try it with the T panel. Already took out 
screws and bent back tangs at top of rear window. just the seal glue 
holding it.
and i will try the oxygen sensor, what should it do if unplugged?
regards
Steve
--- In doc-uk@xxxxxxxxxxxxxxx, "Richard" <dickyh11@xxxx> wrote:
> Hi Steve,
> 
> Nice one! Great feeling isn't it?
> 
> Assuming the wandering revs are at idle, this could be due to a 
duff
> oxygen sensor, unplug it (behind the drivers seat, it comes 
through a
> rubber bung in the bulkhead) and see what happens.
> 
> T panel clearances 'should be' whatever you need to make them so it
> works :)
> Normally lifting the t section (skywards) fixes catching doors. 
Bung
> some bits of cardboard box under it to see if it makes a 
difference,
> then do a proper job with some foam pads. Difficult to advise 
without
> seeing it of course...
> 
> Rich H
> DOC 365 VIN 1274
> 
> > -----Original Message-----
> > From: doc-uk@xxxxxxxxxxxxxxx [mailto:doc-uk@xxxxxxxxxxxxxxx] On 
Behalf
> Of
> > blackaddertoo
> > Sent: 31 July 2005 00:51
> > To: doc-uk@xxxxxxxxxxxxxxx
> > Subject: [doc] finally driven her!!
> > 
> > Hi all
> > 
> > actually finally driven my car after a nearly a year, although 
only
> > a few yards up and down the drive!!.
> > 
> > first time its move under its own power for 12 or so years!.
> > 
> > a few questions if anyone can help.
> > 
> > first the T roof panel, it does now catch after new door
> > struts..i've loosened it but it will only really move up (not 
back)
> > what should the clearance at the corner of the door be? ie how 
far
> > up should it move?.
> > 
> > and the engine...it will run but tends to wonder through the rev
> > range, almost stalling, battery is now low and car is an early 
vin
> > for older alternator. i have not yet replaced injectors, plugs 
etc.
> > any ideas before i take the manifold off?
> > 
> > just want to get it through its MOT first.
> > 
> > jobs done so far... new tank, filter, pipes, pump, baffle, recon
> > calipers, new discs+pads, front bearings, all struts, brake 
pipes,
> > battery, clutch master, clutch slave.
> > if anyone needs tips on these just email.
> > 
> > tahnx all
> > 
> > regards
> > 
> > steve
> > vin1621
> > doc 370
> > 
> > 
> > 
> 
> 
> 
>       
>       
>             
> ___________________________________________________________ 
> Yahoo! Messenger - NEW crystal clear PC to PC calling worldwide 
with voicemail http://uk.messenger.yahoo.com
DOC UK Website: www.deloreans.co.uk
Unsubscribe: doc-uk-unsubscribe@xxxxxxxxxxxxxxx
** Unless otherwise stated, all messages posted to the group are assumed public and may be printed in the club magazine **
  
  
  
  YAHOO! GROUPS LINKS
  
 Back to the Home of PROJECT VIXEN
 Back to the Home of PROJECT VIXEN