Re: [DMCForum] Re: Testing Frequency valve
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [DMCForum] Re: Testing Frequency valve



#7 fuse is good and the Lambda seems to be working because i hear a
clicking noise from the compartment area and the fuel pump is working
too.

I have no power to the Frequency valve, does it get its power directly
from the Lambda or something else (me no good with schematics unless
done in crayon with pretty pictures)?

Mark


cruznmd wrote:

>  1. You can use a dummy probe (Like a screwdriver with a pigtail and a
>
> lightbulb in the handle. $5.00) Put the icepick on one contact and
> clip a paperclip in the pigtail and stick it in the other one. If it
> lights, there's power.
>
> 2. Use a voltmeter to measure for voltage across the contacts.
>
> 3. The valve works hot or cold. Just at different rates. It should
> ALWAYS buzz when the engine is running, or it's bypassed at the RPM
> relay.
>
> 4. You could apply power to it if you could find a way to hook it up
> to the control pressure regulator power plug. They are not close
> enough so you'd have to remove the freq valve or rig a contraption.
>
> 5. Yes, one is a ground wire. Use the schematic in the Bible.
>
> 6. A nuclear reaction or a bolt of lightning can be used to generate
> 1.21 gigawatts.
>
>
> I recently found my freq valve wires to be hanging on by a thread. I
> brushed the plug and the wires fell right off! I had to rig something
> up with a couple of crimp-on spade connectors.
>
> The other place to look is the lambda relay. If this has failed, the
> ECU will not have power and it will not power the freq valve. I'm
> having a brain cramp right now but I also believe there is a fuse for
> this. #7 I think. Verify the lambda module has power.
>
> Rich
>
> --- In DMCForum@xxxxxxxxxxxxxxx, id <ionicdesign@xxxx> wrote:
> > My frequency valve is not buzzing so i have a few questions.
> >
> > How do i test for power to the valve (colored wires)?
> >
> > Does the car have to be warm or cold to test the valve?
> >
> > Can i apply power to the valve to see if it works?
> >
> > There is two wires attached to the valve, is one a ground wire?
> >
> > How do i generate 1.21 jigawatts?
> >
> > the last question was to see if you actually read my questions and
> not
> > just scanned the email.
> >
> > Mark
>
>
>                    Yahoo! Groups Sponsor
                        ADVERTISEMENT
                         [Click Here!]

>
> To unsubscribe from this group, send an email to:
> DMCForum-unsubscribe@xxxxxxxxxxxxxxx
>
>
>
> Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.


[Non-text portions of this message have been removed]



Yahoo! Groups Sponsor	 

ADVERTISEMENT
 
<http://rd.yahoo.com/M=244522.3707890.4968055.1261774/D=egroupweb/S=170512
6215:HM/A=1595054/R=0/SIG=124ukap9t/*http://ashnin.com/clk/muryutaitakenat
togyo?YH=3707890&yhad=1595054> Click Here!	
 
<http://us.adserver.yahoo.com/l?M=244522.3707890.4968055.1261774/D=egroupm
ail/S=:HM/A=1595054/rand=145289441> 	

To unsubscribe from this group, send an email to:
DMCForum-unsubscribe@xxxxxxxxxxxxxxx



Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service
<http://docs.yahoo.com/info/terms/> . 

<<attachment: winmail.dat>>



Home Back to the Home of PROJECT VIXEN 


Copyright ProjectVixen.com. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
DMCForum Mailing List Archive  DMCNews Mailing List Archive  DMC-UK Mailing List Archive

This site contains affiliate links for which we may be compensated