FW: [DML] DMC Parts Free - Pay For Shipping Follow-Up #2 (Long)
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

FW: [DML] DMC Parts Free - Pay For Shipping Follow-Up #2 (Long)



I can't help thinking it would have been much cheaper to source bits in the
UK!

Chris P

-----Original Message-----
From: haneydr@xxxx [mailto:haneydr@xxxx]
Sent: 22 March 2002 01:49
To: dmcnews@xxxxxxxxxxxxxxx
Subject: [DML] DMC Parts Free - Pay For Shipping Follow-Up #2 (Long)


The emergency brake cables and rotors have been spoken for. The spings are
still available.

I have had several requests asking me to share my experience and the cost of
the total project, including an estimate of the labor cost. So here goes.

This was not a cheap job. It all started with a broken passenger side lower
balljoint as I was backing out of the driveway. Thank goodness I wasn't on
the interstate doing 70 mph (112 kph)! Although driving a car up a 3-5%
incline driveway with the front right corner supported by a rolling floor
jack is difficult and nerve wracking!

Since I needed to take the suspension apart anyway, this was a good time to
lower the car and replace the OEM shocks. I also needed a brake job and
since the car was out of action anyway. Then along the way I broke a few
things taking it apart.

I DID ALL THE WORK MYSELF EXCEPT THE ITEMS BELOW THAT NEED SPECIAL TOOLS. I
imagine that you could just take the parts total and estimate that as the
labor cost. Or call a local mechanic or one of the DMC service centers and
ask.

Parts I needed, (all are from PJ Grady unless otherwise noted) and cost are
below:

Master Cylinder $175.00
Rotor Set $499.75
Front Pad Kit $55.00
Rear Pad Kit $45.00
Emergency Brake Pads $60.00
Right E-Brake Cable $54.28
Left E-Brake Cable $47.96
2 Caliper Rebuild Kits (front & rear) $73.44
Pepboys - Brake Fluid/Brake Cleaner/Grease/Anti squeal compound $20.00
DMC Houston- Upper Balljoints $109.60
DMC Houston-Lower Balljoints $171.58
Lower Balljoint reinforcement collars $23.95
High Performance Suspension Kit $680.00
DMC Houston - Wheel Bearings $92.62
DMC Houston - Dust Shield for speedometer (2) $29.38
Checker Auto - Sping Compressor - $55.00
DMC Houston - Bolt for rotor brake shield (another broken part) $.68
Labor to have balljoints pressed into the control arms $60.00 (Local Shop)
Labor to have wheel bearings pressed into the rotors $90.00 (Different Local
shop)- They jacked up the price when they found out it was for a Delorean...
Those B#$#$#d's! Last time I let them do any work for me.

For a grand total of (Shhhh - Don't tell my wife.): $2,346.24 not including
shipping!!!

As I mentioned to somebody else. Toby? (I can see Toby-Tabs in my near
future.) Money sure flys when you're having fun. But I really feel it was
money well spent, other than parts ordered I didn't need.

The job took longer than it should have from the time of the broken ball
joint, about 15 months. Most of that time was waisted, fretting over the
coil springs, I let them intimidate me. But my travel schedule also played a
part, I am only home on the weekend. Once I got started working again, only
weekends, and not more than 4-6 hours a day, with delays waiting for parts
that I broke or forgot to order, it only took me about 4 weeks! Somewhere
around 32-48 hours total. A proffessional would have done it in half the
time or less, I'm sure. (Side note: I'm an accountant by trade and getting
my hands dirty and greasy really bothers me.) Tip: Laundry detergent is hard
on your skin but does a great job of cutting the grease and getting your
hands clean.

I couldn't be happier with the results and boy what a feeling of
satisfaction doing all the work myself! I learned a lot and understand the
suspension and brakes (especially the e-brake, I took the e-brake caliper
assembly(s) apart about 6 times) a lot better! I even feel more confident
driving my car, knowing all those parts are brand new!

Sorry for such a long post but that's the whole story.

Dan Haney
03254
882FUTR




To address comments privately to the moderating team, please address:
moderator@xxxx

To search the archives or view files, log in at
http://groups.yahoo.com/group/dmcnews

Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/








Home Back to the Home of PROJECT VIXEN 


Copyright ProjectVixen.com. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
DMCForum Mailing List Archive  DMCNews Mailing List Archive  DMC-UK Mailing List Archive

This site contains affiliate links for which we may be compensated