[DMCForum] Re: very frustrated!! - starting problem

["Brian" <TK581@xxxxxxxxxxxxx>]

DId you mean make a jumper between '30' and '87'?  There is no 37, 
80.  the relay got warm when I last gave the car a go.  Hope I 
didn't fry anything.

The inertia switch looks fine in regards to a visual scan.  No 
corosion or faulty wiring. the plunger slides well and it even looks 
somewhat new.  I think I'm killing my battery though because 
everything is sounding really weak.  I guess I need to re-charge 
it.  But I check the voltage and it holds at 11.8 which shold be 
enough to at least get it going right?

I think it may be time to get a proffessional because I'm starting 
to get over my head with this!!

   

--- In DMCForum@xxxxxxxxxxxxxxx, "cruznmd" <racuti1@xxxx> wrote:
> Ah, good question. Sorry :)
> 
> At the inertia switch, you need to do a "continuity" check. The 
> ground wire from the fuel pump is black/purple, it goes to the 
> intertia switch. Clip one ohm meter probe to the ground wire on 
the 
> pump, then clip the other one to the black/purple contact on the 
> intertia switch plug. If it reads "open" your fuel pump is 
grounded 
> elsewhere and you need to find it. It's probably fallen off. If it 
> reads "short" then the b/p wire is attached to the harness as it 
> should be.
> 
> Also, inspect the BLACK wire on the inertia switch plug to make 
sure 
> it's grounded properly. Just touch the one probe to the black wire 
> contact and the other probe to the body or frame somewhere. Again, 
> short=good, open/resistance=bad. If the pump is grounded at the 
> switch but the -switch- ain't grounded you'll still have the 
problem. 
> 
> Lastly, (regarding the inertia switch) remove and inspect the 
black 
> box. Look at the contacts. Is the plastic melted around them? The 
> older style were a point of failure. They were underrated. You can 
> also put your ohm meter on the contacts and pull the plunger to 
make 
> sure it's operating properly. Plunger down= short. Plunger up= 
open. 
> This is the correct mode of operation.
> 
> I'm really pushing this grounding issue because you jumpered your 
RPM 
> relay and still only had 00.00 volts (flashing 7v). That clears 
the 
> relay from the problem. BTW, I think your jumper was probably fine.
> 
> Oh hell, I just remembered. DeLoreans use the European habit of 
> switching grounds on and off, not power. Definitely follow the 
steps 
> above, but also jumper the RPM relay again, and measure for 12v on 
> the white/purple wire but do it with a ground OTHER than the 
ground 
> wire on the pump. Use the body or frame somewhere. 
> 
> If you have no voltage, go back to the inertia switch and touch 
> white/purple, and an independent ground again. (Frame/body).
> 
> If you have no voltage THERE, go back to the RPM relay and do it 
> again! Unplug the relay and touch W/P and an independent ground. 
The 
> seat belt mounting bolts make a good ground I think. You're 
tracing 
> the flow, finding the break in the pipe.
> 
> Electricity is just plumbing. Electrons flow instead of water and 
the 
> pipes are really tiny.
> 
> Post your findings when you can.
> 
> Rich A.
> #5335
> 
> --- In DMCForum@xxxxxxxxxxxxxxx, "Brian" <TK581@xxxx> wrote:
> > > Ok, two or three people have told you where the interia switch 
is.
> > 
> > What exactly am I supposed to check here?  It's pluged in and 
it's 
> a 
> > black box... :)
> <snip!>

Yahoo! Groups Sponsor

ADVERTISEMENT

---

Yahoo! Groups Links

• To visit your group on the web, go to:
  http://groups.yahoo.com/group/DMCForum/
   
• To unsubscribe from this group, send an email to:
  DMCForum-unsubscribe@xxxxxxxxxxxxxxx
   
• Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.