[DMCForum] Re: The Village Idiot Returns -- Tank Mod Suggestions Welcome
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[DMCForum] Re: The Village Idiot Returns -- Tank Mod Suggestions Welcome



Hey Andrei,

Good to hear from you after all this time. I saw your work and
thought it was good. Bill could do worse than to get ideas from you.

He told me about his engine self-destruction. It's a sad thing. Just
when he had it running well too.

Rich A.

--- In DMCForum@xxxxxxxxxxxxxxx, Andrei Cular <andreic@xxxx> wrote:
> Bill
>
> First off the pump you need to run is made by Facit, and is
marketed
> under under the Facit name, NAPA, and Fram.  It is the most common
> replacement pump used on aircooled VW.  It is solid state in the
sense
> that it has no brushes, has a built in regulator, and should run
about
> $12 at any parts store.
>
> I'll send you some pictures off the list thursday eve of how I have
my
> tank blocked off.  I really don't want to get lectured again about
fuel
> safety...
>
>
> Andrei
> content22207 wrote:
>
> >To put the ending first: I am soliciting suggestions for securing a
> >plate to my former fuel pump opening. I envision a large circular
disc
> >with a 1/4" tube stuck straight down into my Hervey baffle (filter
> >screen attached). I just need to hold it in place, and keep crap
out
> >of my tank. Cutting the lip off an old baffle might be easiest...
> >
> >The story: While road testing my clutch installation, engine
suddenly
> >developed what could charitably be described as an "oil leak".
Belts
> >were slinging it absolutely everywhere. Entire engine compartment
was
> >coated. Dripped from the timing chain cover like the DeLorean
Valdez
> >(didn't leave oil spots on the pavement -- left amazingly large
> >puddles). My brand new dual exhaust is black from barbequed oil.
Has
> >even been slung out the louver vents all over the exterior (bet I'm
> >made friends at the stop light left & right).
> >
> >Checked timing cover bolts -- all were tight. Reseated the lower 8
in
> >silicone with oversize washers to no effect.
> >
> >Replaced front oil seal (one advantage of not having a muffler
across
> >the back of your car) to no effect.
> >
> >Flooded the "valley of death" as an experiment. Sure enough, water
ran
> >into crank case and foamed my oil.
> >
> >My current block has a hole in it a'la Dave Swingle (who theorizes
> >this will become an ever increasing problem among PRV's that have
> >spent majority of their life sitting outdoors).
> >
> >Since I have a brand spanking new PRV sitting in one corner of the
> >diesel shop, obvious solution is an engine swap on the eve of
Pigeon
> >Forge...
> >
> >Is carbureted A series, so I need 4-6 PSI fuel pressure. Wanted to
go
> >mechanical, but I can't find a pump to fit my block (has a circular
> >opening to the camshaft, not oblong). Volvo used dual electric
pumps
> >even in the early 1970's, not mechanical. A regulator for my
current
> >CI pump would cost more than a rail mounted low PSI model. So too
> >would a low PSI pump in the existing boot. I'm looking at generic
> >industrial pumps, mounted to flat surface, $50 or so.
> >
> >As stated, a tube will run straight down into the tank, attached
to a
> >new low pressure line to the rear of the car. Will probably put the
> >pump back there simply because there's more mounting options.
> >
> >Any suggestions to secure my plate to the tank?
> >
> >Bill Robertson
> >#5939
> >
> >
> >
> >
> >
> >
> >Yahoo! Groups Links
> >
> >
> >
> >
> >
> > 
> >


Yahoo! Groups Sponsor
ADVERTISEMENT
click here


Yahoo! Groups Links



Home Back to the Home of PROJECT VIXEN 


Copyright ProjectVixen.com. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
DMCForum Mailing List Archive  DMCNews Mailing List Archive  DMC-UK Mailing List Archive

This site contains affiliate links for which we may be compensated