Bill, The problem is not limited to 5th. I have an overall lack of power. A shallow acceleration curve from 0 MPH--->. Advance is working. I've checked this repeatedly. There is NO advance at idle. All plug wires check sat. All plugs show proper wear. Block temperature is nominal. I have never -had- an A/C belt on the car. Exhaust pressure is normal compared to other DeLoreans. No glowing parts. All fuel system components are new. I have not checked for drooling injectors because they are new. I guess I could. I have not done a compression check since I put the engine back together. I suppose I could do that too. Martin, Freq valve did have bad connection. I have fixed this and it works correctly now. I hear it all the time. Unfortunately I don't have a CO gas analyzer so I'm doing the dwell method. Perhaps I should pay a visit to Dave S. I think he has 3 analyzers. John, It does sort of seem (to me) to be a lean condition. The car idles great and starts easily but.... Keep 'em coming guys. Rich --- In DMCForum@xxxxxxxxxxxxxxx, "content22207" <brobertson@xxxx> wrote: > Are you saying problem limited to 5th gear? (Reads as if floored in > 5th). That's when my predetonation showed up -- lugging in 5th -- and > you remember can of worms that discussion opened... Is probably too > much to expect 6000 RPM in 5th, but you should be able to pass 4000. > > How does car behave gears 1-4? > > Ensure centrifugal advance working. That's what picks up slack when > vacuum drops (wide open throttle). > > *ENSURE* no spark advance at idle. In early ownership tried attaching > mine to what I thought was ported vacuum (have no cut off solenoid, > nor a microswitch to drive one. PO just left diaphragm loose). In fact > was full manifold vacuum, albeit through extremely small orifice. > Totally killed performance -- 10-13 degrees at idle was actually under > full advance. During acceleration ignition time surely jumped AFTER TDC. > > Do a compression test. My experience has been PRV can lose cylinders > with little noticeable effect on engine behavior (doesn't stumble. > Will rock & roll quite a bit more if you lose whole bank). Yet I still > passed traffic on 3 cylinders after SEDOC. You'd think CO2 > measurements would pick up dead cylinders (smell horribly rich)... Is > block temperature COOLER than normal? > > Ensure all plug wires in fact intact. My #1 is home made replacement > for fatigue cracked wire (less than one year old!), probably during > intake manifold work before I re-routed wiring harness. First time > Louie drove my car was as PRV-5. > > Ensure no injectors dribbling liquid fuel. Think Walt Coe has had > problems with this. > > Check for exhaust obstruction. How much pressure do you feel from > muffler tips? Is system glowing at all? > > Try running without A/C belt -- compressor or idler pulley bearings > may be DOA and putting up resistance. Drop alternator belt and check > for free movement of it and water pump. > > Bill Robertson > #5939 > > >--- In DMCForum@xxxxxxxxxxxxxxx, "cruznmd" <racuti1@xxxx> wrote: > > All right. It turns out I'm NOT going to Las Vegas to attend a > > wedding this weekend. This give me a little extra free time. > > > > Here's the issue I want to work on: > > > > I am STILL missing too much horsepower. I have a shallow acceleration > > curve. I can get the car beyond 4000 RPMS but it takes quite a while. > > I realize that 5th gear is NOT for passing but on relatively shallow > > grades, I can barely maintain speed by flooring it. > > I have driven Mike Cohee's car so I know this isn't my imagination. > > > > I have: > > > > 1. All new fuel components. > > 2. All new ignition components. > > 3. Eliminated all the vacuum leaks I could find. > > 4. Verified the timing & that ignition advance functions correctly. > > 5. Set the CO screw to match Mike's setting (and the manual) > > 6. Verified vacuum hose routing IAW the diagram in the engine cover. > > > > I am missing a functional WOT microswitch but this is not the sole > > cause of my problem. I intend to get into the evap canister area to > > check for more vacuum leaks. > > > > Your suggestions are welcome. Thanks, > > > > Rich Yahoo! Groups Sponsor ADVERTISEMENT <http://rd.yahoo.com/M=194081.4074964.5287182.1261774/D=egroupweb/S=170512 6215:HM/A=1732163/R=0/SIG=11n0nglqg/*http://www.ediets.com/start.cfm?code= 30510&media=zone> click here <http://us.adserver.yahoo.com/l?M=194081.4074964.5287182.1261774/D=egroupm ail/S=:HM/A=1732163/rand=811332688> To unsubscribe from this group, send an email to: DMCForum-unsubscribe@xxxxxxxxxxxxxxx Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service <http://docs.yahoo.com/info/terms/> .
<<attachment: winmail.dat>>